CarViraAutomotive magazine

Home / Article

How to Safely Jack Up a Car: Finding Jack Points and Using Jack Stands

Learn how to jack up a car safely by finding the correct lift points, securing the vehicle, and using jack stands properly. This guide also explains when a factory jack…

How to Safely Jack Up a Car: Finding Jack Points and Using Jack Stands

Raising a vehicle for a flat-tire change, brake inspection, or underbody repair is safe only when the ground, lift point, jack, and support stands are all appropriate. Lift points vary by make, model, year, body style, and powertrain, so the owner’s manual or service information should override any generic diagram. Most important, a jack lifts a vehicle; it is not a safe work stand.

Quick Answer

To jack up a car safely:

  1. Read the vehicle owner’s manual to find the approved jack and jack-stand points.
  2. Park on level, firm ground away from moving traffic. Turn off the vehicle, set the parking brake, select Park or the appropriate gear, and chock the wheels that will remain on the ground.
  3. Use a jack with the correct capacity and lift range. Center it under the designated lifting point.
  4. Raise the vehicle only as high as necessary, keeping everyone clear of the vehicle.
  5. If any part of your body will go underneath, place properly rated jack stands at the specified support points and lower the vehicle onto them before starting work.
  6. Lower the vehicle slowly, torque wheel fasteners to the manufacturer’s specification if a wheel was removed, and check the tire pressure using the vehicle’s recommended cold pressure.

Never work under a vehicle supported only by a jack. If the surface is sloped or soft, the lift point is damaged, or the equipment rating is unclear, stop and use a professional lift or call roadside assistance.

Tools and Equipment Needed

  • The vehicle owner’s manual or model-specific service information
  • A factory jack for an emergency wheel change, or a properly rated floor jack for maintenance work
  • Jack stands with suitable capacity and working height for the vehicle and the job
  • Wheel chocks
  • A lug wrench or breaker bar, plus a torque wrench for wheel installation
  • Work gloves, eye protection, and a flashlight for underbody inspections
  • A spare tire or replacement wheel when performing a tire change

Check the capacity, lift range, and condition of both the jack and the stands. Do not use equipment with hydraulic leaks, bent parts, damaged welds, missing locking hardware, or unreadable ratings. Do not substitute concrete blocks, bricks, buckets, stacked lumber, or a spare tire for jack stands.

A factory scissor or bottle jack is generally intended for the temporary wheel-change procedure described by the automaker. It should not be used as the sole support for an oil change, brake repair, inspection, or any job that requires getting underneath the vehicle.

Why Jack Points and Jack Stands Matter

Jack points are reinforced areas designed to accept lifting force without crushing the body or damaging nearby components. Many unibody cars use reinforced sections of the pinch weld near the wheels. Some pickups and SUVs specify points on the frame, axle housing, or another reinforced structure.

The correct location is not universal. Some vehicles use separate points for the factory jack, a floor jack, and jack stands. A part that looks strong may still be unsuitable. Do not lift from the oil pan, exhaust system, plastic underbody cover, thin floor pan, fuel tank, or a suspension component unless the manufacturer specifically identifies it as a lifting point.

Vehicle-specific note: A jack point shown for an emergency scissor jack may not be the correct support point for a floor jack or jack stand. Follow the vehicle’s instructions for both lifting and supporting the vehicle.

Hybrid and electric vehicles require additional care. Never assume the high-voltage battery enclosure is a lifting point, and do not touch orange high-voltage cables or components. Use only the model-specific lift points; high-voltage repairs should be handled by a properly trained technician.

Before You Start

Complete these checks before placing the jack under the vehicle:

  • Choose a safe location. Use level, solid concrete or sound asphalt. Avoid slopes, loose gravel, soft soil, ice, and surfaces that can sink or allow the jack to roll. If a roadside location is too close to traffic or does not provide a stable shoulder, do not attempt the repair.
  • Read the manual. Check the lifting diagram, transmission and parking-brake instructions, any air-suspension or jacking mode, and the recommended support points.
  • Inspect the vehicle. Do not lift from a jack point that is badly rusted, crushed, bent, or otherwise damaged.
  • Inspect the equipment. Confirm that the jack and stands are in good condition and have suitable ratings. If you cannot determine whether they are appropriate, do not guess.
  • Clear the area. Remove passengers, children, and pets from the vehicle and keep them away from the work area. Let hot exhaust components, brakes, and engine parts cool before working nearby.
  • Secure the vehicle. Set the parking brake, select Park on an automatic transmission, or use the gear recommended by the manual for a manual transmission. Turn off a hybrid or EV completely and follow its parking instructions.
  • Use wheel chocks. Place chocks against the wheels that will remain on the ground. Chocks supplement the parking brake; they do not replace jack stands.
  • Loosen wheel fasteners before lifting. If removing a wheel, break the lug nuts or lug bolts loose slightly while the tire is still on the ground. Do not remove them yet.

Step-by-Step: How to Jack Up a Car Safely

Step 1: Secure the vehicle and prepare the wheel

Confirm that the vehicle is fully off the roadway and that the ground is firm and level. Set the parking brake, select the correct transmission position, and turn the vehicle off. Chock the wheels that will stay on the ground.

For a tire change, loosen the wheel fasteners just enough to break their initial resistance. If the vehicle moves, the chocks shift, or a fastener requires excessive force, stop and correct the problem before lifting.

Step 2: Locate the approved lift point

Use the owner’s manual to identify the exact point for the corner or end you need to raise. Look for the reinforced area described in the instructions rather than relying on a generic location from another vehicle.

Check the contact area for severe corrosion, deformation, or missing metal. If the point is damaged, do not move the jack to a nearby component simply because it appears stronger. Have the vehicle inspected by a qualified technician.

Step 3: Position the jack correctly

Place the jack on a flat part of the hard surface with its saddle centered directly under the approved lift point. The saddle must contact the intended structure evenly. Do not place a loose block or an unapproved adapter between the jack and the vehicle.

If using a floor jack, make sure its base is stable and its wheels can move as the vehicle rises. Keep the jack handle and release control accessible, but do not stand in a position where a sudden shift could trap you.

Do not allow the jack to press against plastic rocker-panel covers, brake lines, fuel lines, wiring, the exhaust, or other components that are not designed to carry the vehicle’s weight.

Step 4: Raise the vehicle slowly

Raise the vehicle gradually while watching the jack saddle, the lift point, and the jack base. Keep hands, feet, and tools away from pinch points, and never crawl underneath to check the contact while the vehicle is being raised.

Stop immediately if the jack tilts, rolls unexpectedly, sinks, the lift point deforms, or the vehicle begins to lean. Move clear of the vehicle before lowering or repositioning it. Do not try to catch or stabilize a shifting vehicle by hand.

Raise the vehicle only high enough for the intended task. For a tire change, that usually means the tire has just cleared the ground. For underbody work, raise it only far enough to install the required stands at their approved support points.

Step 5: Install jack stands before working underneath

Place the stands at the locations specified by the vehicle manufacturer or the service procedure. The jack point and the jack-stand point may be different, so confirm both locations before lifting.

Use the number of stands required for the job, with each stand positioned on the same firm, level surface. Fully engage each stand’s locking mechanism and make sure its base is flat and stable. Never use a stand on loose soil, a sloped surface, or an improvised platform.

Lower the vehicle slowly onto the stands. Before getting underneath, verify from outside the vehicle that each stand is upright, properly seated, and not sinking or tilting. If anything shifts, clear the area and lower the vehicle; do not try to reposition a loaded stand by hand.

A jack left nearby is not a substitute for stands. Never place any part of your body under the vehicle while the jack is the only support.

Step 6: Complete the work and lower the vehicle

Keep the engine off and do not shift the transmission, spin a wheel, or run the drivetrain while the vehicle is raised unless an exact service procedure calls for it and the required professional-grade equipment and precautions are in place.

When reinstalling a wheel, start the lug nuts or bolts by hand to prevent cross-threading. Lower the vehicle as directed by the owner’s manual and tighten the wheel fasteners with a torque wrench using the manufacturer’s specification and sequence. Do not invent a torque value or rely on a generic setting.

Before lowering completely, remove tools and make sure everyone is clear. Use the jack at the approved lifting point to unload the stands, remove them, and lower the vehicle slowly. Once the vehicle is fully on the ground, check the tire pressure against the driver’s-door placard or owner’s manual. The maximum pressure printed on the tire sidewall is not the vehicle’s normal recommended pressure.

Never leave a vehicle unattended while it is supported only by a jack. After a wheel change, follow the owner’s manual for any required fastener recheck before normal driving.

Common Jacking Mistakes to Avoid

MistakeWhy it is dangerousSafer practice
Using the oil pan, exhaust, plastic cover, or an unapproved suspension partThe component can bend, break, or allow the jack to slipUse only the lift point shown in the vehicle instructions
Working under a factory jack or floor jack aloneA jack can shift, roll, or lose pressureSupport the vehicle on properly rated jack stands before going underneath
Lifting on a slope, loose gravel, or soft soilThe jack or stands can sink or move as the load risesRelocate to firm, level ground or call for assistance
Using a damaged or undersized jack or standThe equipment may fail under loadCheck condition and ratings before every use
Raising the vehicle higher than necessaryExtra height increases instability and fall distanceLift only enough for the tire or repair task
Leaving people in the cabin or running the drivetrainMovement can change the vehicle’s balance or create a crushing hazardKeep everyone out and turn the vehicle off
Improvising with blocks, lumber, or other objectsImprovised supports can split, roll, or collapseUse equipment designed and rated for vehicle support

What You Can Inspect Once the Vehicle Is Securely Supported

After the vehicle is fully supported, stable, and cool, a visual inspection may reveal problems that deserve attention. Depending on what is accessible, look for:

  • Torn CV-joint boots or grease splattered around a drive axle
  • Visible brake-fluid leaks, damaged brake hoses, severe rotor scoring, or unusually worn brake pads
  • Oil or fluid leaks from the engine, transmission, differential, or cooling system
  • Wet shock or strut housings, cracked suspension bushings, bent parts, or obvious looseness
  • Corroded, hanging, or damaged exhaust components and heat shields
  • Severe underbody rust or damage from road debris
  • Inner-sidewall damage, uneven tire wear, or objects lodged in the tire

These are visual checks, not a complete diagnosis. Do not touch hot, pressurized, electrical, or moving components, and do not pull on steering or suspension parts unless the service procedure specifically calls for it. Brake, steering, and suspension concerns should be evaluated by a qualified technician when the condition is unclear.

When to See a Mechanic Instead

Use a professional shop or roadside service when:

  • You cannot find a level, firm area away from traffic.
  • The vehicle’s lift points are hidden, damaged, badly corroded, or unclear.
  • The jack leaks, will not hold height, tilts, or has damaged or missing hardware.
  • The stands do not fit the specified support points or cannot sit flat.
  • The vehicle has air suspension and you do not know the required jacking mode.
  • The job involves coil springs, struts, steering components, brake hydraulics, fuel-system parts, airbags or SRS components, or high-voltage hybrid or EV systems.
  • The repair would require running the engine or rotating the drivetrain while the vehicle is raised.

A knowledgeable DIY owner can perform some tire and brake maintenance with the correct service information and support equipment. When the procedure involves stored spring energy, pressurized systems, high voltage, or a safety-critical diagnosis, professional equipment and training are the safer choice.

FAQ

Can I work under a car supported by the factory jack?

No. Use the factory jack only for the temporary wheel-change procedure described by the automaker, and keep your body out from underneath. Any inspection or repair that requires underbody access needs properly rated jack stands or a professional vehicle lift.

Where should I put the jack on my car?

Use the exact lifting point shown in the owner’s manual. Many cars have reinforced pinch-weld sections near the wheels, while trucks and SUVs may specify frame or axle locations. Do not assume that a point used on another vehicle is safe for yours.

How many jack stands do I need?

There is no universal number. Use the number and locations required by the vehicle and repair procedure. Never support an entire vehicle or an elevated end with a single jack, and never go underneath while the jack is the only support.

Can I jack up a car on a gravel driveway?

Loose gravel and soft or sloped ground can let the jack or stand sink and shift. Move the vehicle to a firm, level surface if possible. If there is no safe location, call roadside assistance rather than trying to level the area with loose boards or other improvised materials.

What should I do if the jack starts to slip or lower?

Stay clear of the vehicle and do not reach underneath or try to catch it. If it can be lowered safely from outside according to the equipment instructions, do so; otherwise keep the area clear and call roadside or professional assistance. Remove the jack from service until it has been inspected or replaced.

Can I use the same jacking procedure on a hybrid or EV?

Only if the vehicle’s manual specifies the lifting points and procedure. Do not lift from the high-voltage battery enclosure or work near orange high-voltage cables. Repairs involving the high-voltage system should be performed by a trained technician.

Leave a Comment